Project Checklist

Home>
Project Checklist

1 Business Information

2 Sheet Metal

3 Mechanical Piping

4 Laser Scanning

5 Plumbing

6 Electrical

7 Questions About Project

Business Information
Email*
Project Name?*
Business Name?
Name
First Last

Sheet Metal
If your project does not include sheet metal, please skip this entire section by scrolling to the bottom of the page and hitting "next."
Does your Project Require Sheet Metal?
- Yes
- No
Please check the following contract documents that will be provided to MLP.
- PDF Contract Available
- Revit Files Available
- ACAD Files Available
Shop Drawings Issue for Approval.
- Yes
- No
This is the basic issue showing routing, sizes, and equipment tags. It is used to go over the design with the sheet metal superintendent and issue to the GC, engineer, etc.
Shop Drawings Sleeves and Blockouts
- Yes
- No
ShopDrawings Issue for Construction/Fabrication.
- Yes
- No
This adds elevations, dimensions, and duct tags.
Level 0 Coordination.
- Yes
- No
Does not include elevations and is per contract – no design change.
Level 1 Coordination.
- Yes
- No
Includes Level 0 and minor design changes, value engineering, converting from rectangle to round when 12” and under.
Level 2 Coordination.
- Yes
- No
Includes level 1 and coordination between the ceiling and structure only.
Level 3 Coordination.
- Yes
- No
Includes level 2 and “Full BIM” This is LOD 400 and is coordinated between other trades.
Hangers and Supports.
- Yes
- No
Trimble or total station files
- Yes
- No
MAJ Files
- Yes
- No
Shop Drawings As-Built.
- Yes
- No
These are derived from redlines from the field for needed modifications.

Mechanical Piping
If your project does not include mechanical piping, please skip this entire section by scrolling to the bottom of the page and hitting "next."
Does your project require mechanical piping?
- Yes
- No
Please check the following contract documents that will be provided to MLP
- PDF Contract Available
- REvit Files Available
- ACAD Files Available
Shop Drawings Issue for Approval.
- Yes
- No
This is the basic issue showing routing, sizes, and equipment tags. It is used to go over the design with the sheet metal superintendent and issue to the GC, engineer, etc.
Shop drawings sleeves and blockouts.
- Yes
- No
Shop Drawings Issue for Construction/Fabrication.
- Yes
- No
This adds elevations, dimensions, and duct tags.
Level 0 Coordination.
- Yes
- No
Does not include elevations and is per contract – no design change.
Level 1 Coordination.
- Yes
- No
Includes level 0 and minor design changes, value engineering, includes checking pipe velocity, pipesizes, etc.
Level 2 Coordination.
- Yes
- No
Includes level 1 and coordination between the ceiling and structure only.
Level 3 Coordination.
- Yes
- No
Includes level 2 and “Full BIM” This is LOD 400 and is coordinated between other trades.
Hangers and Supports.
- Yes
- No
Trimble or total station files.
- Yes
- No
Spools for piping 2 1⁄2” and larger.
- Yes
- No
Spools for piping 2” and smaller in mechanical rooms.
- Yes
- No
Spools for pipe racks.
- Yes
- No
BOM, Bill of Materials.
- Yes
- No
Shop Drawings As-Built.
- Yes
- No
These are derived from redlines from the field for needed modifications.

Laser Scanning
If your project does not include laser scanning, please skip this entire section by scrolling to the bottom of the page and hitting "next."
Does your include project Laser Scanning?
- Yes
- No
Please check the following contract documents that will be provided to MLP
- On-site laser scanning with point cloud model
- Conversion of point cloud to solids/surfaces for a BOM or that can be clashed against in Navisworks.

Plumbing
If your project does not include plumbing, please skip this entire section by scrolling to the bottom of the page and hitting "next."
Does your project require plumbing
- Yes
- No
Please check the following contract documents that will be provided to MLP
- PDF Contract Available
- Revit Files Available
- ACAD Files Available
Plumbing sanitary waste and vent.
- Yes
- No
Plumbing pressure, domestic water, and gas.
- Yes
- No
Medical Gases.
- Yes
- No
Shop Drawings Issue for Approval.
- Yes
- No
This is the basic issue showing routing, sizes, and equipment tags. It is used to go over the design with the plumbing superintendent and issue to the GC, engineer, etc.
Shop drawings sleeves and blockouts.
- Yes
- No
Shop Drawings Issue for Construction/Fabrication.
- Yes
- No
This adds elevations, dimensions, and duct tags.
Level 0 Coordination.
- Yes
- No
Does not include elevations and is per contract – no design change.
Level 1 Coordination.
- Yes
- No
Includes level 0 and minor design changes, value engineering, includes checking fixture counts against pipe sizes.
Level 2 Coordination.
- Yes
- No
Includes level 1 and coordination between the ceiling and structure only.
Level 3 Coordination.
- Yes
- No
Includes level 2 and “Full BIM” This is LOD 400 and is coordinated between other trades.
Hangers and Supports.
- Yes
- No
Trimble or total station files.
- Yes
- No
Spools for piping 2 1⁄2” and larger.
- Yes
- No
Spools for piping 2” and smaller in mechanical rooms.
- Yes
- No
Spools for pipe racks.
- Yes
- No
BOM, Bill of Materials.
- Yes
- No
Shop Drawings As-Built.
- Yes
- No
These are derived from redlines from the field for needed modifications.

Electrical
If your project does not include electrical, please skip this entire section by scrolling to the bottom of the page and hitting "next."
Does your project require electrical?
- Yes
- No
Please check the following contract documents that will be provided to MLP
- PDF Contract Available
- Revit Files Available
- ACAD Files Available
Cable Tray and bus duct modeling with clearances.
- Yes
- No
Electrical Conduit 2” and larger or banks of conduit.
- Yes
- No
Electrical Conduit 2” and smaller or deck 90’s.
- Yes
- No
Lighting and fixtures.
- Yes
- No
Equipment, panels, and transformers.
- Yes
- No
Fire Alarm and Special systems (radio, security, satellite, etc.)
- Yes
- No
Shop Drawings Issue for Approval.
- Yes
- No
- Maybe
This is the basic issue showing routing, sizes, and equipment tags. It is used to go over thedesign with the electrical superintendent and issue to the GC, engineer, etc.
Shop drawings sleeves and blockouts.
- Yes
- No
Shop Drawings Issue for Construction/Fabrication.
- Yes
- No
This adds elevations, dimensions, and duct tags.
Coordination. “Full BIM”
- Yes
- No
This is LOD 400 and is coordinated between trades.
Hangers and Supports.
- Yes
- No
Trimble or Total Station files.
- Yes
- No
BOM, Bill of Materials.
- Yes
- No
Shop Drawings As-Built.
- Yes
- No
These are derived from redlines from the field for needed modifications.

Questions About Project.
These are general questions regarding your project. Feel free to skip any questions you are unsure about.
APPROX. START DATE?
Date Format: MM slash DD slash YYYY
ARE EQUIPMENT SUBMITTALS AVAILABLE, IF NOT HOW SOON WILL THEY BE AVAILABLE AFTER THE START DATE?
WILL EQUIPMENT BE PROVIDED IN A 3D FORMAT (REVIT OR ACAD)?
ESTIMATED FIELD LABOR HOURS?
APPROX. SQUARE FOOTAGE?
NUMBER OF FLOORS?
ADDITIONAL INFORMATION NEEDED TO CONSIDER?
Upload Blueprints
Drop files here or

Accepted file types: pdf, gif, png, ai, eps, jpg, psd.